How do you adjust the band on a 48RE transmission?

How do you adjust the band on a 48RE transmission?

theunit

1. Raise vehicle.
2. Loosen band adjusting screw locknut. Then back.
3. Tighten band adjusting screw to 8 N·m (72 in. lbs.)
4. Back off front band adjusting screw 1-3/4 turns, for. diesel vehicles, or 1-1/2 turns, for V-10 vehicles.
5. Hold adjuster screw in position and tighten locknut to 41 N·m (30 ft. lbs.)
6. Lower vehicle.

What years did dodge use the 48RE transmission?

The 48RE is a 4 speed automatic transmission, it was manufactured between the years 2002 to 2010. It was a direct replacement for the Dodge Ram 2500 and 3500 series trucks.

Is the 48RE good?

Registered. The main weak spots, in general, of the 48RE are: line pressure, torque converter and the input shaft due to it’s locked 3-4 shift. Other than those, they’re a pretty good towing transmission.

What does 48RE stand for?

Follow along as we look at the origins, development, and installation of a Dodge 48RE transmission, which stands for: (4) four speeds, (8) level eight torque rating, (R) rear-wheel drive, and (E) electronically controlled transmission. Simpson Planetary Gearset.

How many gears does a 48RE transmission have?

The 48RE transmission has electronic shift controls and a four-speed gear layout, including overdrive.

How do you adjust the bands on a c6 transmission?

Adjusting the bands is a straight forward process. Just get the car safely up on jacks. Locate the intermediate band adjustment (the front one), loosen the locknut, torque down the adjustment screw to 10 ft lbs and then loosen it exactly 1 1/2 turns. Tighten locknut.

Will changing transmission fluid stop slipping?

For low fluid levels, you’ll need to add more fluid to repair the problem. For burnt or damaged fluid, you’ll need to drain the exhausted fluid and replace it with new fluid. For a leak, however, at least part of your transmission will need to be resealed to prevent further slipping and transmission problems.

Is the 48RE a 5 speed?

The 48re is a 4 speed. The only thing you can do would be to put an over/under on it.

How many gears are in a 48RE?

How Much ATF does a 48RE hold?

The 48re takes ATF+4 transmission fluid and has a 14.5 – 16.5 quart dry fill capacity. When dropping the transmission pan to perform a standard drain and fill transmission fluid change, you can expect to replace around anywhere from 5-7 quarts of fluid assuming the stock transmission pan is being used.

Does the 48RE have overdrive?

The 48RE transmission has electronic shift controls and a four-speed gear layout, including overdrive. For example, it engages the torque converter lockup and does not allow overdrive.

How to adjust the band adjustment on a 4848re transmission?

48RE Band Adjustment? 1. Raise vehicle. 2. Remove transmission oil pan and drain fluid. 3. Loosen band adjusting screw locknut 5-6 turns. Be sure adjusting screw turns freely in lever. 4. Tighten adjusting screw to 8 N·m (72 in. lbs.) torque. 5. Back off adjusting screw 3 turns. 6. Hold adjusting

How do you tighten the band adjusting screw on a Honda Accord?

1. Raise vehicle. 2. Loosen band adjusting screw locknut. Then back locknut (1) off 3-5 turns. Be sure adjusting screw turns freely in case. Apply lubricant to screw threads if necessary. 3. Tighten band adjusting screw to 8 N·m (72 in. lbs.) torque with an appropriate Torx™ socket.

What happened to the 47 and 48RE?

The 47 and 48RE evolved over the years from the bullet proof 727 3 speed trans of the early 60’s. In it’s hay day, it was the trans of envy. It evolved to a lock up converter and an overdrive transmission. In the early days, the overdrive units were a problem and the torque converters. But that was designed that way for warranty purposes.